Wi-Fi Turbo Vita changelog
v0.7.2 · Nov 14, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
Fixed since v0.7.1
- No more battery drain with Wi-Fi off. Keep Wi-Fi on stops the Vita going to sleep by itself, so that Wi-Fi stays connected. It kept doing that after Wi-Fi had been switched off or airplane mode turned on, when there is nothing to keep connected: a Vita left alone like that never slept and ran its battery down. Now, with Wi-Fi off or airplane mode on, the Vita goes to sleep on its timer exactly as it does without Wi-Fi Turbo, and the idle keep-alive pauses too. Switch Wi-Fi back on and Keep Wi-Fi on takes over again. Thanks to u/ali_ihsan21 on Reddit for the report.
Also new
- The log says when the Vita may sleep, and why.
wifiturbo.lognow gets a line each time Keep Wi-Fi on starts or stops holding off sleep, with the reason (on battery, charging, Wi-Fi off, power button pressed), so a battery report can show what was going on.
Everything else is unchanged from v0.7.1.
Install or update
- Download
wifiturbo_kernel.skprx,wifiturbo.suprxandwifiturbo_settings.suprxbelow. - Copy them to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - Updating from v0.7.0 or v0.7.1: nothing to change in
config.txt, and your settings are kept. Updating from v0.6.2 or older:wifiturbo_settings.suprxis a new file since v0.7.0, so copy it too; see the v0.7.0 notes. New install: add the lines from the README to yourconfig.txt. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on and Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
5e03301fab9a635159234afcf724cf252014ae084370bb1217c27f9527a730a1 wifiturbo_kernel.skprx 9cafafd210a2dafe6dfc519333ed5fcda2238146a7460bc926c9ad9446a10385 wifiturbo.suprx 9aaf9945591e6a1c7a1ac1afc3fb1483ee0966a206371953c8088200997199bf wifiturbo_settings.suprx 63a4c272cf3ba52f436d5921280cf76d3e6e8b98b2f5b6dd3494656dbf0ee871 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.7.1 · Nov 3, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
Fixed since v0.7.0
- Music keeps playing with the screen off. Without Wi-Fi Turbo, pressing the power button while the Music app is playing just turns the screen off and the music carries on. With Keep Wi-Fi on, Wi-Fi Turbo put the Vita to sleep 2 seconds after the press, which stopped the music. Now it checks first: while music is playing, the press only turns the screen off, and the Vita sleeps by itself once the music ends or is paused. With no music playing, a press still sleeps the Vita as before. If the music still stops for you, please say so in #21. Thanks @AlexAnorak for the report (#21).
Also new
- The log names your real firmware. HENkaku's version spoofing can make a Vita report 3.74 when it runs an older firmware. The log now adds a line with the firmware the home screen really comes from, for example
firmware: home screen is the 3.60 build, so bug reports show the right version (thanks @YxngOck, whose report in #19 showed the need).
Everything else is unchanged from v0.7.0.
Install or update
- Download
wifiturbo_kernel.skprx,wifiturbo.suprxandwifiturbo_settings.suprxbelow. - Copy them to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - Updating from v0.7.0: nothing to change in
config.txt, and your settings are kept. (wifiturbo_settings.suprxandwifiturbo_qm.suprxare the same as in v0.7.0.) Updating from v0.6.2 or older:wifiturbo_settings.suprxis a new file since v0.7.0, so copy it too; see the v0.7.0 notes. New install: add the lines from the README to yourconfig.txt. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
e609ab7000402187ab18358eb391719f154da995864a2fd201c15c1554f3038d wifiturbo_kernel.skprx a6090405aeda976ada6abcd0b196065958f824723b14d4eb078eb6c631348040 wifiturbo.suprx 9aaf9945591e6a1c7a1ac1afc3fb1483ee0966a206371953c8088200997199bf wifiturbo_settings.suprx 63a4c272cf3ba52f436d5921280cf76d3e6e8b98b2f5b6dd3494656dbf0ee871 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.7.0 · Nov 2, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
⚠️ Breaking change: there is now a third file
The Wi-Fi Turbo page in Settings has moved into its own file, wifiturbo_settings.suprx. If you update wifiturbo.suprx without copying the new file as well, the Wi-Fi Turbo page disappears from Settings (everything else keeps working). See Updating from v0.6.x or older below: it is one extra file, and your config.txt can stay as it is.
The Slimmening
The home screen (SceShell) has a small, fixed amount of memory that every *main plugin shares. When it runs out, parts of the system quietly go missing: the on-screen keyboard, the LiveArea's waves and reflections, or an app's LiveArea freezing. With many plugins installed, Wi-Fi Turbo was part of that squeeze.
v0.7.0 takes most of Wi-Fi Turbo out of the home screen:
- The Settings page is its own module. Its code, its text in 20 languages and its page buffers used to sit in the home screen all the time, though only the Settings app uses them. Now they load only while Settings is open.
- The log is no longer also kept in memory. It was only there for a developer command, which now reads the log file.
- The quick menu toggles carry only their own six labels, instead of a copy of every Settings string.
| Home-screen memory | v0.6.2 | v0.7.0 | Saved |
|---|---|---|---|
| wifiturbo.suprx | 186 KB | 63 KB | −123 KB (−66%) |
| wifiturbo_qm.suprx (quick menu toggles, optional) | 78 KB | 8 KB | −70 KB (−90%) |
| Both | 264 KB | 71 KB | −193 KB (−73%) |
Measured on a PS Vita (3.60): the memory the home screen could still allocate after boot went from 1,796 KB to 1,992 KB with this build, the same 196 KB.
Why it matters: that memory goes back to the home screen and your other plugins, so more of them fit together before the keyboard or the LiveArea starts to suffer. If you saw the keyboard or the LiveArea waves go missing, or an app's LiveArea freeze, with many plugins installed (#4, #5), please try v0.7.0 and let us know.
Nothing else changes: same features, same settings (they are kept), same behaviour.
Updating from v0.6.x or older
- Download
wifiturbo_kernel.skprx,wifiturbo.suprxand the newwifiturbo_settings.suprxbelow. - Copy all three to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. config.txt: nothing to change. Your existingur0:tai/wifiturbo.suprxline under*NPXS10015now loads the Settings page from the new file. Optional, tidier: change that line tour0:tai/wifiturbo_settings.suprx. Don't list the same file twice; if both lines are there, it still works (the second copy steps aside).- Reboot, then open Settings → Network → Wi-Fi Turbo.
Wi-Fi Turbo page missing after updating? wifiturbo_settings.suprx isn't in ur0:tai/: copy it there and reboot. ur0:data/wifiturbo/wifiturbo.log names the missing file.
New install
- Download
wifiturbo_kernel.skprx,wifiturbo.suprxandwifiturbo_settings.suprxbelow, and copy them tour0:tai/. - Add one line under each of three sections of your
config.txt(ux0:tai/config.txtif it exists, otherwiseur0:tai/config.txt):
| Section | Line to add |
|---|---|
| *KERNEL | ur0:tai/wifiturbo_kernel.skprx |
| *main | ur0:tai/wifiturbo.suprx |
| *NPXS10015 | ur0:tai/wifiturbo_settings.suprx |
- Reboot, then open Settings → Network → Wi-Fi Turbo. The README has the full steps.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
82854a85633ba7403620bb910dc97a11c1f254889a27c61b97d16778bf822b9d wifiturbo_kernel.skprx 9903736aee282d62de7ab6f1837d8cf13c6ab57e5861e9db77f8f3c3d44639ce wifiturbo.suprx 9aaf9945591e6a1c7a1ac1afc3fb1483ee0966a206371953c8088200997199bf wifiturbo_settings.suprx 63a4c272cf3ba52f436d5921280cf76d3e6e8b98b2f5b6dd3494656dbf0ee871 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.6.2 · Nov 2, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
Fixed since v0.6.1
- Airplane mode is respected. With airplane mode on, Wi-Fi no longer turns itself back on after the Vita wakes from sleep. Airplane mode switches Wi-Fi off but leaves the Wi-Fi setting itself on, and Auto-reconnect on drop only looked at that setting. Now it also checks airplane mode: Wi-Fi stays off, and if you switch Wi-Fi back on while in airplane mode, it reconnects as usual. HUD only on problems no longer counts airplane mode as a problem either. Thanks @DionKill for the report (#20).
Everything else is unchanged from v0.6.1.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Reports of MAC address (especially Per network) on 3.71 to 3.74 are especially welcome. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
7e14bc070a788a36588a07fb865a12cf324663ae514c2968073e974f01b0959a wifiturbo_kernel.skprx 42c4629b2782412461c184767229dfd4ebf8cdff934c74511dcfff2c00b47941 wifiturbo.suprx ae9dd36128f83a740e64b2c2f967d0a56b95f9092f3ce43da4dd52917c80e506 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.6.1 · Nov 1, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
What's new since v0.6.0
- HUD only on problems. A new HUD option: the HUD stays hidden while Wi-Fi is working well, and appears while Wi-Fi is disconnected, connecting or getting an address (DHCP), or when the signal stays at or below your Roaming signal level. It hides again 5 s after things recover, so you see it come back up first. Turning Wi-Fi off yourself doesn't count as a problem. In all 20 system languages.
- The HUD settings have moved to sit together between Wi-Fi receive buffer and MAC address, in the same order as before.
Fixed
- Smart Mesh Roaming no longer depends on an extra driver hook added in v0.6.0 for Per network. If that one hook couldn't be installed on a console, roaming would have stopped working too; now only Per network is affected (it then stays off).
- The Per network key is no longer shared with other apps through Wi-Fi Turbo's Settings state.
- Per network starts before the system's first Wi-Fi scan more reliably after a very short boot (for example, switching the Vita off within 30 s of turning it on).
- A reconnect after waking is no longer left waiting while Auto-reconnect on drop is off, to fire later when it's turned back on.
- Settings help: the HUD's MAC address line shows in Custom and Per network mode. The remote-control
helplists the newer commands.
Everything else is unchanged from v0.6.0.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Reports of MAC address (especially Per network) on 3.71 to 3.74 are especially welcome. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
6386929e84a6ea3046818b834a9cd92b62e57ca33587d2918e248b5c87129279 wifiturbo_kernel.skprx 72a18014a7a300a7e9778fc9be0b963269ff507f5d563163d5b4e09658534930 wifiturbo.suprx ae9dd36128f83a740e64b2c2f967d0a56b95f9092f3ce43da4dd52917c80e506 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.6.0 · Nov 1, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
What's new since v0.5.1
- A MAC address per network (Settings → Network → Wi-Fi Turbo → MAC address → Per network). Every Wi-Fi network gets its own address, the same each time you connect to it, like the private addresses on phones: your home router keeps seeing one device, but different networks can't tell they're seeing the same console, or that it's a PS Vita. In all 20 system languages.
- The address is set before the Vita joins a network, from the moment it starts up.
- While not connected, the Vita looks for networks with a random address, a new one after each disconnect.
- If an address can't be set, the Vita doesn't connect rather than use the wrong one.
- Reconnects straight after waking. After sleep, Wi-Fi Turbo asks the Vita to connect at once (and again 3 s later if needed) instead of waiting for the system's own retry.
- Roaming signal level. Choose how weak the signal must stay before Smart Mesh Roaming looks for a stronger access point: -65, -70, -75 (the previous fixed level, still the default) or -80 dBm. Greyed out while roaming is off.
- HUD data rate. An optional line on the HUD, in both Compact and Extended, with the current download and upload speed:
DOWN 12.3 Mb/s UP 0.4 Mb/s. It reads the Wi-Fi driver's own counters once a second, so it costs next to nothing.
Everything else is unchanged from v0.5.1.
Good to know about Per network
- Switching to it disconnects Wi-Fi for a few seconds. Each network then sees a new device: expect a different IP address, and anything set up for the old address (a reserved IP, a MAC filter) won't apply.
- The addresses come from a random key made once on your Vita and kept with Wi-Fi Turbo's settings. Resetting those settings makes a new key, so every network sees a new address.
- Going back to an older Wi-Fi Turbo: it reads Per network as Custom, and saving any setting with it drops the key, so after updating again every network sees a new address.
- Holding L at boot (no plugins) always starts on the Vita's own address.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Reports of MAC address (especially Per network) on 3.71 to 3.74 are especially welcome. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console. With Per network on, a console where the address can't be set won't connect to Wi-Fi: choose Default to get back online.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
81893a76e1d6340848027ab40fc766f9f99c275f223d3b731b6d4f969c596144 wifiturbo_kernel.skprx e120ba16ed7c3dc2e6e9089b3981ab0c7edec88b8b99ff05ebfd95c6c13d61cc wifiturbo.suprx 0b25deff4400b2952145d9c1314063f8c6a6a5ded154b9202f74b4d663506018 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.5.1 · Oct 31, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
A bug-fix release. Everything else is unchanged from v0.5.0.
Fixed
- The Vita could crash at boot with some other plugins installed (#17). With some plugin combinations the system finished loading its network libraries later than usual, and Wi-Fi Turbo called into one before it had loaded. Wi-Fi Turbo now waits until they have loaded. Thanks to rhobiusvoid for the report and the boot log.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
687dd783b4a0ac5f31e74bcb253a8d256067fe4608aab776882e8a0473ad5390 wifiturbo_kernel.skprx c6c383449b4909ba18a90d35045f50d5858c387f6ede9b9aa60d5e279f9d4738 wifiturbo.suprx 78416b8f3447d9a00932c3afb550e42f5839b2590edfb4cb69131e2bc553df51 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.5.0 · Oct 31, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The MAC address option is experimental and tested on 3.60.
What's new since v0.4.1
- MAC address (Settings → Network → Wi-Fi Turbo): use the Vita's own Wi-Fi MAC address, or a custom one. Type your own, or press Randomize MAC address for a new one that keeps the maker half of the Vita's own. A Current MAC address row shows the address in use, marked not applied if the custom one didn't take. In all 20 system languages.
- Two HUD sizes. Wi-Fi HUD overlay is now Off, Compact or Extended, the same choices as Turbo Storage's HUD. Compact is a single line (network, signal and channel); Extended is the full HUD, plus the MAC address in use while the MAC address is set to Custom. If you had the HUD on, it's now Extended, so nothing changes.
Everything else is unchanged from v0.4.1.
Fixed
- Wi-Fi connecting, dropping and connecting again at boot. With the Wi-Fi receive buffer on Enhanced or Maximum, the setting was re-applied about 20 s after the Vita connected, which cost a short drop. It is now applied as soon as Wi-Fi turns on, before the Vita connects, so it connects once.
- Keep Wi-Fi switching the radio back on in the middle of a receive-buffer change. It now waits for the change to finish.
- The power button could stop putting the Vita to sleep if the system's network service stopped responding while Keep Wi-Fi on was holding standby off. The power button is now handled on its own, and if the network side stays stuck for a minute the standby hold is released.
- A receive-buffer change could leave Wi-Fi showing as connected with nothing getting through. After the power-cycle, Wi-Fi now only counts as back once your router answers, and the Vita restarts if it stops answering in the next minute and a half, as it already did when Wi-Fi never came back. On networks where the router doesn't answer, it works as before.
- Settings could be lost if the Vita crashed or lost power while saving them. They are now saved whole or not at all.
- A quick menu or Settings change could, rarely, be lost if both were used at the same moment.
How the MAC address behaves
- Default uses the Vita's own address. Custom uses the Custom MAC address. Choosing Custom makes a new random address, and typing an address switches to Custom. Custom MAC address and Randomize MAC address are greyed out in Default.
- Any change disconnects Wi-Fi for a few seconds and reconnects with the new address. Your router sees a new device: the Vita will likely get a different IP address, and anything set up for its old address (a reserved IP, a MAC filter) won't apply to the new one.
- A custom address is set again automatically after a reboot, before the Vita first connects, and after sleep.
- Addresses that can't work are refused: anything that isn't 12 hex digits (colons optional), multicast addresses, all zeros and all FFs.
- Nothing is changed permanently. Default restores the Vita's own address, and holding L at boot (no plugins) always starts on it.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. Using the quick menu toggles? Also replacewifiturbo_qm.suprxin yourQuickMenuRebornfolder. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Reports of MAC address on 3.71 to 3.74 are especially welcome. Redact your network name (SSID) and MAC addresses from the logs first.
Known limitations
- MAC address has only run on 3.60. Sony rebuilt the Wi-Fi driver in 3.71; the parts it uses are the same there, but 3.71 to 3.74 is untested on a console.
- Changing the MAC address, the power profile or the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Checksums (SHA-256)
5ac71152074013b7c7d45d45405e89848dccdefb1f1f41858b0b58a54b9fd72f wifiturbo_kernel.skprx a4ebd1d8b22cf293f94ad7251a58e56a783368ecf3fa32d94053e60cb8d4d29d wifiturbo.suprx fd6c8425baa4378b721f1bf48edbe42e482a496fbb56899cca9d612885d9491b wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.4.1 · Oct 29, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet.
What's new since v0.4.0
Quick menu polish, from #13:
- 🔤 The profile buttons fit in every language. The quick menu now uses short names for its three buttons (for example Desempenho / Equilibrado / Economia in Portuguese), so they no longer spill past the buttons. The Settings page keeps the full names.
- 📶 A Wi-Fi icon on the Keep Wi-Fi on row, lined up with the system's own rows.
Installing is unchanged: the icon is built into wifiturbo_qm.suprx.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow and copy them tour0:tai/, replacing the older copies. - Using the quick menu toggles? Also replace
wifiturbo_qm.suprxin yourQuickMenuRebornfolder. - Reboot.
New to Wi-Fi Turbo? Follow the README.
Checksums (SHA-256)
030b3fcb62a2b2387ac2bbef7ece889da020396f45f5cb706b675b8af2fb441f wifiturbo_kernel.skprx c4d8d2877a59408fcef1590c54b2b6b05e3ddee526b3f089983f105e3a7ba297 wifiturbo.suprx 46930af983f0678b762998274c98e5c37309159da1924a2f5c7e1dda7b684176 wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.4.0 · Oct 29, 2026
Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet.
What's new since v0.3.1-alpha
- Quick menu toggles (optional). Keep Wi-Fi on and the Wi-Fi power profile in the PS button quick menu, so you can switch them in the middle of a game. The rows show the current setting every time the menu opens, and a change there is applied and saved exactly like one made in Settings. Changing the power profile reconnects Wi-Fi for a few seconds. In all 20 system languages.
- Follows the system language without a reboot. The quick menu rows switch language the next time you open the menu.
- The Settings page picks up changes. After changing something in the quick menu, leave the Wi-Fi Turbo page and open it again to see the new value; Settings no longer needs restarting.
Everything else is unchanged from v0.3.1-alpha.
Quick menu toggles: install
The quick menu rows are a separate, optional file, wifiturbo_qm.suprx. They need QuickMenuReborn, the community library other plugins use for their quick-menu rows.
- If you don't have QuickMenuReborn yet: copy
QuickMenuReborn.suprxtour0:tai/and add it under*mainin your config file, then copyqmr_plugin.rcotour0:QuickMenuReborn/. Both are on QuickMenuReborn's release page. - Copy
wifiturbo_qm.suprxbelow toux0:QuickMenuReborn/if that folder exists, otherwise tour0:QuickMenuReborn/. It doesn't go inconfig.txt. - Reboot, wait a few seconds on the Home screen, then press the PS button.
To remove the rows, delete wifiturbo_qm.suprx.
Install or update
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing the older copies. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), whether you use other quick-menu plugins, what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and access point MAC addresses from the logs first.
Known limitations
- If the Wi-Fi Turbo Settings page is open while you change something in the quick menu, it shows the new value only after you leave the page and come back.
- Another plugin's uninstaller may remove QuickMenuReborn along with its own files; if the quick menu rows disappear, reinstall QuickMenuReborn.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita.
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
Credits
The quick menu rows use QuickMenuReborn by Ibrahim (MIT).
Checksums (SHA-256)
5d678547c1ee74985a4c5ec23023e0dec08575a5ede46260ac8caf6867bec705 wifiturbo_kernel.skprx bbfd64bfbe8b6257d864d5a05b86f844852a18bb2c3e5737accd5ebc7ef1e05d wifiturbo.suprx 6cf560fcd598bd6accd8cf119526a82d5f08d8e1b5a5e15bd8ab1949b057902e wifiturbo_qm.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.3.1-alpha · Oct 29, 2026
Alpha. Runs on every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console; the others are not yet. The Wi-Fi receive buffer option is experimental.
What's new since v0.2.0
- Wi-Fi receive buffer (Settings → Network → Wi-Fi Turbo): Default, Enhanced or Maximum. It re-divides the Wi-Fi chip's memory in a way Sony never intended, very much in the spirit of Crash Bandicoot's PlayStation tricks, so bursts of incoming data stop overflowing it. Enhanced gives incoming data 53 % more room, Maximum 80 %.
- Faster TCP. Same-session measurements, 40 MHz and Max performance:
| Comparison | UDP download | TCP download | TCP upload |
|---|---|---|---|
| Stock (20 MHz, Balanced) vs Turbo with buffer Maximum | 44.0 → 69.5 Mbps (+58%) | 34.2 → 50.4 Mbps (+47%) | |
| Buffer Default vs Enhanced | 65.0 → 69.5 Mbps (+7%) | 34.4 → 40.2 Mbps (+17%) | |
| Buffer Default vs Maximum | 62.7 → 67.4 Mbps (+7%) | 42.6 → 50.4 Mbps (+18%) | 19.5 → 39.1 Mbps (2×) |
Compare within a row: signal strength differed between sessions.
- Firmware 3.60 to 3.74. Sony rebuilt the Wi-Fi driver in 3.71; the plugin knows both driver builds, checks every patch site before using any of them, and switches driver features off (and says so in the log) on a driver it doesn't recognise.
- HUD position: the overlay can sit in any screen corner.
- The HUD stays out of your games. It now shows on the Home screen, in Settings and in the quick menu, so pressing the PS button in a game brings it up. Turn on In-game HUD in Settings to keep it over games and apps too, for example while streaming.
speedtestno longer hangs the remote-control port if a transfer stalls.
Fixed
- Battery drain in "sleep" (#8). With Keep Wi-Fi on, the power button used to only turn the screen off, so a Vita that looked asleep stayed awake and ran its battery flat. A press of the power button now really puts it to sleep.
- Charging stopped at about 89 % (#6). Keep Wi-Fi on no longer holds the Vita awake while it is charging, so it can reach 100 %.
- Boot hang at the health and safety screen on some 3.65 setups (#2). The plugin now waits for the system to finish setting up the network before it starts. Not yet confirmed by an affected user: please report back.
Keep Wi-Fi on and sleep
Keep Wi-Fi on stops the Vita going into standby by itself, so downloads and remote sessions survive. That means:
- When the screen turns off on its timer, the Vita is not asleep. It stays awake and connected, and keeps using battery. Pressing the power button just turns the screen back on.
- To put it to sleep, press the power button once. That always works, even with Keep Wi-Fi on. Changed your mind? Press again straight away and it stays awake. After it wakes, Wi-Fi reconnects within about 15–30 s.
- Holding the power button opens the power menu as usual.
- While charging, the Vita is allowed to go into standby on its own, so the battery fills to 100 %.
If you want the Vita to go into standby by itself as normal, turn Keep Wi-Fi on off.
How the receive buffer behaves
- Changing it turns Wi-Fi off and on for about 20 seconds. If Bluetooth is on, it is switched off for those few seconds too (the chip only resets with both off); paired devices reconnect by themselves. The Bluetooth icon in the status bar does not change.
- After a reboot the setting is re-applied automatically about 20 s after the Vita connects (one short Wi-Fi drop).
- If a change ever fails to bring Wi-Fi back, the Vita restarts and the next boot falls back to Default.
- Firmware: the Wi-Fi chip runs one of two firmware builds: one on 3.60–3.65 (tested on 3.60) and one on 3.67–3.74 (not yet tested on a console).
Supported firmware
| Firmware | Status |
|---|---|
| 3.60, 3.65, 3.68 | Tested |
| 3.61, 3.63, 3.67, 3.69, 3.70, 3.71, 3.72, 3.73, 3.74 | Alpha, not yet tested on a console |
| Anything else | Not supported, don't install |
Install
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing any older copies. - If you're new to Wi-Fi Turbo, add the lines from the README to your
config.txt. Updating: nothing to change, your settings are kept. - Reboot, then open Settings → Network → Wi-Fi Turbo.
If anything goes wrong, hold L while the Vita boots to skip all plugins, then go back to v0.2.0.
Testers: please report
Open an issue with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what you noticed, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log. Redact your network name (SSID) and access point MAC addresses from the logs first.
Known limitations
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
- With Keep Wi-Fi on, a screen that has turned off on its timer is not sleep: press the power button once to sleep the Vita (see above).
- Changing the power profile, roaming, or changing the receive buffer briefly drops the connection, which also ends any FTP transfer in progress.
- Smart Mesh Roaming takes roughly 12–18 s and only moves between access points with the same network name.
Checksums (SHA-256)
84f4dbe54c6b8f5415f1327ad6283f15ca0847ac17d49eebb1757906d35cf453 wifiturbo_kernel.skprx 0e41a8a9dc60f4eaccc8df1b0aaf3476fe62cd65fd62fa88f950462e726c1d64 wifiturbo.suprx
Provided as is, with no warranty. See the README's disclaimer.
v0.2.1-alpha · Oct 25, 2026
Alpha: every firmware from 3.60 to 3.74. 3.60, 3.65 and 3.68 are tested on a console and behave exactly like v0.2.0, so stay on v0.2.0 there unless you want to help test. The other versions (3.61, 3.63, 3.67 and 3.69 to 3.74) are not yet tested on a console.
What's new since v0.2.0
- Firmware 3.71 to 3.74. Sony rebuilt the Wi-Fi driver in 3.71, which moved the code the plugin patches. Older versions leave 40 MHz, power profiles, Smart Mesh Roaming and the SNR readout switched off there. This release knows both driver builds and picks the right one at start-up.
- Firmware 3.61, 3.63, 3.67, 3.69 and 3.70 are now listed too. They use the same driver build as 3.60–3.68.
- Safer on unknown firmware. The plugin now checks every patch site of a driver build before using any of them. If the driver matches no known build, all driver features stay off and the log says so.
- The kernel log names the driver build it found (
wlanbt: SceWlanBt layout ...), to help with bug reports.
Everything else is unchanged from v0.2.0.
Supported firmware
| Firmware | Status |
|---|---|
| 3.60, 3.65, 3.68 | Tested |
| 3.61, 3.63, 3.67, 3.69, 3.70, 3.71, 3.72, 3.73, 3.74 | Alpha, not yet tested on a console |
| Anything else | Not supported, don't install |
Install
- Download
wifiturbo_kernel.skprxandwifiturbo.suprxbelow. - Copy both to
ur0:tai/, replacing any older copies. - Add to
ur0:tai/config.txt(if a section already exists, add the line under it; if you have aux0:tai/config.txt, use that file instead):
*KERNEL ur0:tai/wifiturbo_kernel.skprx *main ur0:tai/wifiturbo.suprx *NPXS10015 ur0:tai/wifiturbo.suprx
- Reboot, then open Settings → Network → Wi-Fi Turbo.
Updating from v0.2.0: replace both files and reboot. Your settings are kept.
If anything goes wrong, hold L while the Vita boots to skip all plugins, then remove the lines. Full instructions are in the README.
Testers wanted
Please open an issue either way, with your firmware, how you run HENkaku (Ensō, h-encore, HENlo), what works and what doesn't, and ur0:data/wifiturbo/wifiturbo.log and ur0:data/wifiturbo/wifiturbo_kernel.log after a boot. Useful checks: the Wi-Fi Turbo page appears under Settings → Network, the HUD shows an SNR, 40 MHz connects at 40 MHz on a 40 MHz access point, and switching power profiles reconnects cleanly. Redact your network name (SSID) and access point MAC addresses from the logs first.
Known limitations
- Only 3.60, 3.65 and 3.68 have run on a console so far. On the other versions a feature that can't find what it expects switches itself off and logs why, rather than risk a crash.
- While Keep Wi-Fi on is enabled, the power button only turns the screen off; the Vita stays awake and connected. Turn the option off to let it sleep.
- Smart Mesh Roaming takes roughly 12–18 s and briefly drops the connection, and only moves between access points with the same network name.
Checksums (SHA-256)
25534fd9a66da06d89330afe71e270e5010e9a093bc81952f1fae46a8a34233d wifiturbo_kernel.skprx 12fa356a845321ca006bff3dd091be85bf7fc50f1a61e38ebccc3a10828678cb wifiturbo.suprx
Provided as is, with no warranty. See the README's disclaimer.
