VitaBrightEX LUT Editor v1.3 by Zushikina-kun
Companion app for VitaBrightEX that allows to edit LUT configurations for the plugin.
Install on your Vita
In VitaShell, hold Left on the D-pad and press ○ to open the QR code scanner, then point the Vita's back camera at the code.
| File | Size | |
|---|---|---|
| VitaBrightEX-LUT-Editor-v4.2.vpk 7e4123fb…22d8 | 448 KB | Hide code Download |
| VitaBrightEX-v1.3.zip 27703213…4ab1 | 17 KB | QR code Download |
Data: the developer's notes say what the app needs. Scan its code the same way, then press ✕ on the zip in ux0:download/ to open it. Mark everything inside (△ › Mark all), copy it (△ › Copy), then go to the folder the developer's notes name and paste it (△ › Paste). You can delete the zip afterwards.
Other ways to install
Copy it to the memory card: copy VitaBrightEX-LUT-Editor-v4.2_brewology_com.vpk to ux0: (USB or FTP in VitaShell), open it in VitaShell and press ✕ to install it.
Screenshots
About VitaBrightEX LUT Editor
VitaBrightEX v1.3 + LUT Editor v4.2
Critical fixes in this release
OLED: presets no longer destroy screen colours
The previous OLED screen filter applied CCT/gamma/contrast math directly
to the panel's 21-byte LUT rows. Those bytes are panel hardware control
registers — not linear RGB pixel values. Applying a colour matrix to them
produced wrong results and made every single preset look worse than the
default. This is now fully fixed.
The OLED LUT is left completely untouched by the filter system. Your
screen colour is set by the calibrated per-panel LUT file
(vitabright_lut_p5.txt etc.) loaded at boot — which already has the
correct white-point for your specific panel. Factory reset restores
this clean state instantly.
Tab switching now works reliably
The app was using sceCtrlPeekBufferPositiveExt2 which remaps the
physical L/R shoulder buttons to different bit positions (L1/R1 DS4
style) that the code wasn't reading. Fixed: uses plain
sceCtrlPeekBufferPositive so the physical L/R buttons correctly
switch tabs.
What each part now does
Plugin v1.3
- OLED colour is controlled by the per-panel LUT file only
- Filter math (CCT/gamma/contrast) is NOT applied to OLED — it was the wrong architecture and destroyed calibration
- Hardware invert (sceDisplaySetInvertColorsForDriver) still works
- LCD filter (IFTU CSC matrix) unchanged — works correctly
App v4.2 on Vita 1000 (OLED):
- Tab 1: Invert toggle + Factory reset — the only safe options
- Tab 2: Invert only, with explanation of why CCT/gamma/contrast are not shown (to prevent accidentally breaking colours)
App v4.2 on Vita 2000 (LCD):
- Tab 1: Full CCT preset list (6500K–1200K) + IPS/sRGB/Night/Boost enhancements — correct because IFTU CSC applies to pixel data
- Tab 2: Temperature / Gamma / Contrast / Brightness / Invert sliders
Factory reset (Triangle): Calls vitabrightOledReload() to restore
the clean panel LUT from the panel-specific file on disk, then clears
invert. Restores original colours immediately without a reboot.
Installation
- Extract VitaBrightEX-v1.3.zip and copy all files to ur0:/tai/
- Add ur0:/tai/vitabright.skprx under *KERNEL in ur0:/tai/config.txt
- Reboot
- Install VitaBrightEX-LUT-Editor-v4.2.vpk via VitaShell
If ux0:/tai/ exists on your memory card it takes priority over ur0:/tai/.
Based on vitabright by devnoname120 (https://github.com/devnoname120/vitabright).
Screen filter inspired by Luma3DS Rosalina (https://github.com/LumaTeam/Luma3DS).
Release notes
v1.3 · VitaBrightEX-LUT-Editor-v4.2.vpk · Aug 18, 2026
VitaBrightEX v1.3 + LUT Editor v4.2
Critical fixes in this release
OLED: presets no longer destroy screen colours
The previous OLED screen filter applied CCT/gamma/contrast math directly
to the panel's 21-byte LUT rows. Those bytes are panel hardware control
registers — not linear RGB pixel values. Applying a colour matrix to them
produced wrong results and made every single preset look worse than the
default. This is now fully fixed.
The OLED LUT is left completely untouched by the filter system. Your
screen colour is set by the calibrated per-panel LUT file
(vitabright_lut_p5.txt etc.) loaded at boot — which already has the
correct white-point for your specific panel. Factory reset restores
this clean state instantly.
Tab switching now works reliably
The app was using sceCtrlPeekBufferPositiveExt2 which remaps the
physical L/R shoulder buttons to different bit positions (L1/R1 DS4
style) that the code wasn't reading. Fixed: uses plain
sceCtrlPeekBufferPositive so the physical L/R buttons correctly
switch tabs.
What each part now does
Plugin v1.3
- OLED colour is controlled by the per-panel LUT file only
- Filter math (CCT/gamma/contrast) is NOT applied to OLED — it was the wrong architecture and destroyed calibration
- Hardware invert (sceDisplaySetInvertColorsForDriver) still works
- LCD filter (IFTU CSC matrix) unchanged — works correctly
App v4.2 on Vita 1000 (OLED):
- Tab 1: Invert toggle + Factory reset — the only safe options
- Tab 2: Invert only, with explanation of why CCT/gamma/contrast are not shown (to prevent accidentally breaking colours)
App v4.2 on Vita 2000 (LCD):
- Tab 1: Full CCT preset list (6500K–1200K) + IPS/sRGB/Night/Boost enhancements — correct because IFTU CSC applies to pixel data
- Tab 2: Temperature / Gamma / Contrast / Brightness / Invert sliders
Factory reset (Triangle): Calls vitabrightOledReload() to restore
the clean panel LUT from the panel-specific file on disk, then clears
invert. Restores original colours immediately without a reboot.
Installation
- Extract VitaBrightEX-v1.3.zip and copy all files to ur0:/tai/
- Add ur0:/tai/vitabright.skprx under *KERNEL in ur0:/tai/config.txt
- Reboot
- Install VitaBrightEX-LUT-Editor-v4.2.vpk via VitaShell
If ux0:/tai/ exists on your memory card it takes priority over ur0:/tai/.
Based on vitabright by devnoname120 (https://github.com/devnoname120/vitabright).
Screen filter inspired by Luma3DS Rosalina (https://github.com/LumaTeam/Luma3DS).
